小弟是个新手，我的磁盘阵列有三块硬盘报错，请问如何处理？
HSZ80>; show disk
Name Type Port Targ Lun Used by
------------------------------------------------------------------------------
DISK10000 disk 1 0 0 FAILEDSET
DISK10100 disk 1 1 0 R02
DISK20000 disk 2 0 0 FAILEDSET
DISK20100 disk 2 1 0 R02
DISK30000 disk 3 0 0 R01
DISK30100 disk 3 1 0 R02
DISK40000 disk 4 0 0 R02
DISK40100 disk 4 1 0 R01
DISK50000 disk 5 0 0 R01
DISK50100 disk 5 1 0 R02
DISK60000 disk 6 0 0 FAILEDSET
DISK60100 disk 6 1 0 R01
请高手指点一二，小弟谢谢了！！！！
robert 回复于：2005-01-02 09:21:19
不知你的 spare set 有几块硬盘。
DISK10000 disk 1 0 0 FAILEDSET
DISK20000 disk 2 0 0 FAILEDSET
DISK60000 disk 6 0 0 FAILEDSET
上面的三块硬盘已被替换下来了。
就怕spare set 里没有硬盘了。再有坏的硬盘的话，就没有盘可以替换上去了。
你用下面命令，看看全面的信息。
HSZXXX>;SHOW THIS_CONTROLLER FULL
HSZXXX>;SHOW OTHER_CONTROLLER FULL
HSZXXX>;SHOW DEVICES FULL
HSZXXX>;SHOW device-name
HSZXXX>;SHOW STORAGESETS FULL
HSZXXX>;SHOW storageset-name
HSZXXX>;SHOW UNITS FULL
HSZXX>;show failedset
HSZXX>;show spareset
HSZXX>;show emu
qqaazz-ydy 回复于：2005-01-02 10:05:47
这是我用命令查看的信息情况，我下一步该怎么做？能不能把这三块报错的硬盘再添加上？请问怎么添加？小弟在这里谢谢了！！！！！！！
HSZXXX>;SHOW THIS_CONTROLLER FULL
Controller:
HSZ80 ZG00208585 Software V83Z-0, Hardware E04
NODE_ID = 5000-1FE1-0006-5770
ALLOCATION_CLASS = 0
SCSI_VERSION = SCSI-2
Configured for dual-redundancy with ZG00208631
In dual-redundant configuration
Device Port SCSI address 7
Time:
Host PORT_1:
SCSI target(s) (1, 2)
Preferred target(s) (1)
TRANSFER_RATE_REQUESTED = 20MHZ
Host Functionality Mode = A
Command Console LUN is target 1, lun 6
Host PORT_2:
SCSI target(s) (3, 4)
Preferred target(s) (3)
TRANSFER_RATE_REQUESTED = 20MHZ
Host Functionality Mode = A
Cache:
32 megabyte write cache, version 0022
Cache is GOOD
Unflushed data in cache
CACHE_FLUSH_TIMER = DEFAULT (10 seconds)
Mirrored Cache:
32 megabyte write cache, version 0022
Cache is GOOD
Unflushed data in cache
Battery:
FULLY CHARGED
Expires: 02-DEC-2002
WARNING: BATTERY AT END OF LIFE WITHIN ONE WEEK, REPLACE BATTERY SOON!
NOCACHE_UPS
Extended information:
Terminal speed 9600 baud, eight bit, no parity, 1 stop bit
Operation control: 00000000 Security state code: 30730
Configuration backup disabled
HSZXXX>;SHOW OTHER_CONTROLLER FULL
Controller:
HSZ80 ZG00208631 Software V83Z-0, Hardware E04
NODE_ID = 5000-1FE1-0006-5770
ALLOCATION_CLASS = 0
SCSI_VERSION = SCSI-2
Configured for dual-redundancy with ZG00208585
In dual-redundant configuration
Device Port SCSI address 6
Time: NOT SET
Host PORT_1:
SCSI target(s) (1, 2)
Preferre
TRANSFER_RATE_REQUESTED = 20MHZ
Host Functionality Mode = A
Command Console LUN is target 1, lun 6
Host PORT_2:
SCSI target(s) (3, 4)
Preferred target(s) (4)
TRANSFER_RATE_REQUESTED = 20MHZ
Host Functionality Mode = A
Cache:
32 megabyte write cache, version 0022
Cache is GOOD
Unflushed data in cache
CACHE_FLUSH_TIMER = DEFAULT (10 seconds)
Mirrored Cache:
32 megabyte write cache, version 0022
Cache is GOOD
Unflushed data in cache
Battery:
FULLY CHARGED
Expires: WARNING: UNKNOWN EXPIRATION DATE!
WARNING: AN UNKNOWN NUMBER OF DEEP DISCHARGES HAVE OCCURRED!
NOCACHE_UPS
Extended information:
Terminal speed 9600 baud, eight bit, no parity, 1 stop bit
Operation control: 00000000 Security state code: 8489
Configuration backup disabled
HSZXXX>;SHOW DEVICES FULL
Name Type Port Targ Lun Used by
------------------------------------------------------------------------------
DISK10000 disk 1 0 0 FAILEDSET
Misconfigured: No device at this PTL, please see user guide
DISK10100 disk 1 1 0 R02
COMPAQ BD009122C6 B016
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
LOCAL
Size: 17769177 blocks
DISK20000 disk 2 0 0 FAILEDSET
COMPAQ BD009122C6 B016
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
LOCAL
Size: NOT YET KNOWN
DISK20100 disk 2 1 0 R02
COMPAQ BD009122C6 B016
Sw
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
LOCAL
Size: 17769177 blocks
DISK30000 disk 3 0 0 R01
COMPAQ BD009122C6 B016
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
LOCAL
Size: 17769177 blocks
DISK30100 disk 3 1 0 R02
COMPAQ BD009122C6
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
LOCAL
Size: 17769177 blocks
DISK40000 disk 4 0 0 R02
COMPAQ BD009122C6 B016
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
LOCAL
Size: 17769177 blocks
DISK40100 disk 4 1 0 R01
COMPAQ BD009122BA 3B09
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
LOCAL
Size: 17769177 blocks
DISK50000 disk 5 0 0 R01
COMPAQ BD009122C6 B016
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
LOCAL
Size: 17769177 blocks
DISK50100 disk 5 1 0 R02
COMPAQ BD009122C6 B016
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
LOCAL
Size: 17769177 blocks
DISK60000 disk 6 0 0 FAILEDSET
Misconfigured: No device at this PTL, please see user guide
DISK60100 disk 6 1 0 R01
COMPAQ BB00911CA0 3B05
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
LOCAL
Size: 17769177 blocks
HSZXXX>;SHOW device-name
HSZXXX>;SHOW STORAGESETS FULL
Name Storageset Uses Used by
------------------------------------------------------------------------------
R01 raidset DISK30000 D100
DISK40100 D101
DISK50000 D102
DISK60100 D103
D104
D105
Switches:
POLICY (for replacement) = BEST_PERFORMANCE
RECONSTRUCT (priority) = NORMAL
CHUNKSIZE = 256 blocks
State:
REDUCED
DISK60100 (member 0) is NORMAL
DISK30000 (member 2) is NORMAL
DISK40100 (member 3) is NORMAL
DISK50000 (member 4) is NORMAL
Size: 71059340 blocks
Partitions:
Partition number Size St
--------------------------------------------------------------------
1 7105531 ( 3638.03 MB) 0 D100
2 14211067 ( 7276.06 MB) 7105536 D101
3 14211067 ( 7276.06 MB) 21316608 D102
4 14211067 ( 7276.06 MB) 35527680 D103
5 14211067 ( 7276.06 MB) 49738752 D104
6 7109511 ( 3640.06 M
R02 raidset DISK10100 D200
DISK20100 D201
DISK30100 D202
DISK40000 D203
DISK50100 D204
D205
Switches:
POLICY (for replacement) = BEST_PERFORMANCE
RECONSTRUCT (priority) = NORMAL
CHUNKSIZE = 256 blocks
State:
NORMAL
DISK10100 (member 0) is NORMAL
DISK20100 (member 1) is NORMAL
DISK30100 (member 2) is NORMAL
DISK40000 (member 3) is NORMAL
DISK50100 (member 4) is NORMAL
Size: 71059340 blocks
Partitions:
Partition number Size Starting Block Used by
--------------------------------------------------------------------
1 7105531 ( 3638.03 MB) 0 D200
2 14211067 ( 7276.06 MB) 7105536 D201
3 14211067 ( 7276.06 MB) 21316608 D202
4 14211067 ( 7276.06 MB) 35527680 D203
5 14211067 ( 7276.06 MB) 49738752 D204
6 7109511 ( 3640.06 MB) 63949824 D205
SPARESET spareset
FAILEDSET failedset DISK10000
DISK20000
DISK60000
Switches:
AUTOSPARE
HSZXXX>;SHOW storageset-name
HSZXXX>;SHOW UNITS FULL
LUN Uses
--------------------------------------------------------------
D100 R01 (partition)
LUN ID: 6000-1FE1-0006-5770-0009-0020-8585-004A
Switches:
RUN NOWRITE_PROTECT READ_CACHE
READAHEAD_CACHE WRITEBACK_CACHE
MAXIMUM_CACHED_TRANSFER_SIZE = 32
Access:
Access path = ALL
State:
ONLINE to this controller
Reserved
PREFERRED_PATH = THIS_CONTROLLER
Size: 7105531 blocks
Geometry (C/H/S): ( 2103 / 20 / 169 )
D101 R01
LUN ID: 6000-1FE1-0006-5770-0009-0020-8585-004C
Switches:
RUN NOWRITE_PROTECT READ_CACHE
READAHEAD_CACHE WRITEBACK_CACHE
MAXIMUM_CACHED_TRANSFER_SIZE = 32
Access:
Access path = ALL
State:
ONLINE to this controller
Reserved
PREFERRED_PATH = THIS_CONTROLLER
Size: 14211067 blocks
Geometry (C/H/S): ( 4205 / 20 / 169 )
D102 R0
LUN ID: 6000-1FE1-0006-5770-0009-0020-8585-004D
Switches:
RUN NOWRITE_PROTECT READ_CACHE
READAHEAD_CACHE WRITEBACK_CACHE
MAXIMUM_CACHED_TRANSFER_SIZE = 32
Access:
Access path = ALL
State:
ONLINE to this controller
Reserved
PREFERRED_PATH = THIS_CONTROLLER
Size: 14211067 blocks
Geometry (C/H/S): ( 4205 / 20 / 169 )
D103 R0
LUN ID: 6000-1FE1-0006-5770-0009-0020-8585-004E
Switches:
RUN NOWRITE_PROTECT READ_CACHE
READAHEAD_CACHE WRITEBACK_CACHE
MAXIMUM_CACHED_TRANSFER_SIZE = 32
Access:
Access path = ALL
State:
ONLINE to this controller
Reserved
PREFERRED_PATH = THIS_CONTROLLER
Size: 14211067 blocks
Geometry (C/H/S): ( 4205 / 20 / 169 )
D104 R0
LUN ID: 6000-1FE1-0006-5770-0009-0020-8585-004F
Switches:
RUN NOWRITE_PROTECT READ_CACHE
READAHEAD_CACHE WRITEBACK_CACHE
MAXIMUM_CACHED_TRANSFER_SIZE = 32
Access:
Access path = ALL
State:
ONLINE to this controller
Reserved
PREFERRED_PATH = THIS_CONTROLLER
Size: 14211067 blocks
Geometry (C/H/S): ( 4205 / 20 / 169 )
D105 R0
LUN ID: 6000-1FE1-0006-5770-0009-0020-8631-0023
Switches:
RUN NOWRITE_PROTECT READ_CACHE
READAHEAD_CACHE WRITEBACK_CACHE
MAXIMUM_CACHED_TRANSFER_SIZE = 32
Access:
Access path = ALL
State:
ONLINE to this controller
Reserved
PREFERRED_PATH = THIS_CONTROLLER
Size: 7109511 blocks
Geometry (C/H/S): ( 2104 / 20 / 169 )
D200 R02
LUN ID: 6000-1FE1-0006-5770-0009-0020-8585-004B
Switches:
RUN NOWRITE_PROTECT READ_CACHE
READAHEAD_CACHE WRITEBACK_CACHE
MAXIMUM_CACHED_TRANSFER_SIZE = 32
Access:
Access path = ALL
State:
ONLINE to the other controller
PREFERRED_PATH = OTHER_CONTROLLER
Size: 7105531 blocks
Geometry (C/H/S): ( 2103 / 20 / 169 )
D201 R02 (p
LUN ID: 6000-1FE1-0006-5770-0009-0020-8631-0026
Switches:
RUN NOWRITE_PROTECT READ_CACHE
READAHEAD_CACHE WRITEBACK_CACHE
MAXIMUM_CACHED_TRANSFER_SIZE = 32
Access:
Access path = ALL
State:
ONLINE to the other controller
PREFERRED_PATH = OTHER_CONTROLLER
Size: 14211067 blocks
Geometry (C/H/S): ( 4205 / 20 / 169 )
D202 R02 (
LUN ID: 6000-1FE1-0006-5770-0009-0020-8631-0027
Switches:
RUN NOWRITE_PROTECT READ_CACHE
READAHEAD_CACHE WRITEBACK_CACHE
MAXIMUM_CACHED_TRANSFER_SIZE = 32
Access:
Access path = ALL
State:
ONLINE to the other controller
PREFERRED_PATH = OTHER_CONTROLLER
Size: 14211067 blocks
Geometry (C/H/S): ( 4205 / 20 / 169 )
D203 R02 (
LUN ID: 6000-1FE1-0006-5770-0009-0020-8631-0028
Switches:
RUN NOWRITE_PROTECT READ_CACHE
READAHEAD_CACHE WRITEBACK_CACHE
MAXIMUM_CACHED_TRANSFER_SIZE = 32
Access:
Access path = ALL
State:
ONLINE to the other controller
PREFERRED_PATH = OTHER_CONTROLLER
Size: 14211067 blocks
Geometry (C/H/S): ( 4205 / 20 / 169 )
D204 R02 (
LUN ID: 6000-1FE1-0006-5770-0009-0020-8631-0029
Switches:
RUN NOWRITE_PROTECT READ_CACHE
READAHEAD_CACHE WRITEBACK_CACHE
MAXIMUM_CACHED_TRANSFER_SIZE = 32
Access:
Access path = ALL
State:
ONLINE to the other controller
PREFERRED_PATH = OTHER_CONTROLLER
Size: 14211067 blocks
Geometry (C/H/S): ( 4205 / 20 / 169 )
D205 R02 (partition)
LUN ID: 6000-1FE1-0006-5770-0009-0020-8631-0025
Switches:
RUN NOWRITE_PROTECT READ_CACHE
READAHEAD_CACHE WRITEBACK_CACHE
MAXIMUM_CACHED_TRANSFER_SIZE = 32
Access:
Access path = ALL
State:
ONLINE to the other controller
PREFERRED_PATH = OTHER_CONTROLLER
Size: 7109511 blocks
Geometry (C/H/S): ( 2104 / 20 / 169 )
HSZXX>;show failedset
Name Storageset Uses Used by
------------------------------------------------------------------------------
FAILEDSET failedset DISK10000
DISK20000
DISK60000
Switches:
AUTOSPARE
HSZXX>;show spareset
Name Storageset Uses Used by
------------------------------------------------------------------------------
SPARESET spareset
HSZXX>;show emu
EMU cabinet settings
EMU Microcode V1.3
Sensor_1_Setpoint 47 degrees C.
Sensor_2_Setpoint 47 degrees C.
Sensor_3_Setpoint 37 degrees C.
Fanspeed AUTOMATIC
Cab 0 IO module Information
Port 1: Single Ended
Port 2: Single Ended
Port 3: Single Ended
Port 4: Single Ended
Port 5: Single Ended
Port 6: Single Ended
robert 回复于：2005-01-02 12:10:52
没有问题，只是没有富余的盘了，以后raid 里有坏盘的话，没有盘可以自动顶上去了。
tru64 回复于：2005-01-02 14:10:44
删除坏盘，增加新盘的顺序为：
show disk
del failedset disk60000
del disk60000
加入新硬盘
add disk disk60000
add spareset disk60000
ok!
对其它的几块盘以此类推！
qqaazz-ydy 回复于：2005-01-03 10:18:39
我已经把坏盘给删除了，但为什么我添加新盘时，添加不上？？请帮忙说的详细一点，非常着急，谢过了！！！
lxlab 回复于：2005-01-03 11:22:58
在 add spareset disk60000 前需要init disk6000就可以了
lxlab 回复于：2005-01-03 11:25:42
上面只是个例子，看好是哪块盘，一定不要弄错了。可以用locate disk60000 定位坏盘。
qqaazz-ydy 回复于：2005-01-03 11:46:22
我使用了，你给我的命令怎么还不行呀？？告诉我是incomplete command ??我用add disk disk10000 ?命令出现SCSI port number，我该怎么写？能不能告诉我详细一点，我是个新手对磁盘柜不是很熟悉。
lxlab 回复于：2005-01-03 22:24:49
我知道HSZ70 的步骤是这样的:
1 show failedset
2 del failedset disk10200
3 del disk10200
4 拔出disk10200 插入新平盘
5 add disks disk10200 1 2 0
6 init disk10200
7 add sparesets disk10200
lxlab 回复于：2005-01-03 22:28:44
你再试试吧,我觉得应该是一样的. 要不就看看随机的文档吧,应该写得很清楚的.
netkey 回复于：2005-01-04 11:26:44
引用：原帖由 "qqaazz-ydy"]我使用了，你给 |
|
